diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 62d751f..f683427 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -775,9 +775,9 @@
 
   // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 159.51
-  #define DEFAULT_bedKi  30.16
-  #define DEFAULT_bedKd 562.43
+  #define DEFAULT_bedKp 124.85
+  #define DEFAULT_bedKi  24.94
+  #define DEFAULT_bedKd 416.57
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #else
@@ -879,8 +879,8 @@
 
 #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
 #define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
-#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
-#define THERMAL_PROTECTION_COOLER  // Enable thermal protection for the laser cooling
+//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+//#define THERMAL_PROTECTION_COOLER  // Enable thermal protection for the laser cooling
 
 //===========================================================================
 //============================= Mechanical Settings =========================
@@ -1511,7 +1511,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { -30, -5, -1.2 }
+#define NOZZLE_TO_PROBE_OFFSET { -40, -10, -3.2 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1571,7 +1571,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 4
 //#define EXTRA_PROBING    1
 
 /**
@@ -1591,9 +1591,9 @@
 #define Z_CLEARANCE_DEPLOY_PROBE   10 // (mm) Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  5 // (mm) Z Clearance between probe points
 #define Z_CLEARANCE_MULTI_PROBE     5 // (mm) Z Clearance between multiple probes
-//#define Z_AFTER_PROBING           5 // (mm) Z position after probing is done
+#define Z_AFTER_PROBING           10 // (mm) Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // (mm) Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -3 // (mm) Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
 #define Z_PROBE_OFFSET_RANGE_MIN -30
@@ -1670,9 +1670,9 @@
 // @section motion
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR true
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_X_DIR false
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
 //#define INVERT_I_DIR false
 //#define INVERT_J_DIR false
 //#define INVERT_K_DIR false
@@ -1905,7 +1905,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1920,7 +1920,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1991,23 +1991,23 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 5
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
-  //#define PROBE_Y_FIRST
+  #define PROBE_Y_FIRST
 
   #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
 
     // Beyond the probed grid, continue the implied tilt?
     // Default is to maintain the height of the nearest edge.
-    //#define EXTRAPOLATE_BEYOND_GRID
+    #define EXTRAPOLATE_BEYOND_GRID
 
     //
     // Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
     //
-    //#define ABL_BILINEAR_SUBDIVISION
+    #define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points
       #define BILINEAR_SUBDIVISIONS 3
@@ -2208,7 +2208,7 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of flash. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save flash.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
@@ -2248,13 +2248,13 @@
 //
 #define PREHEAT_1_LABEL       "PLA"
 #define PREHEAT_1_TEMP_HOTEND 180
-#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_TEMP_BED     50
 #define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
-#define PREHEAT_2_LABEL       "ABS"
+#define PREHEAT_2_LABEL       "PETG"
 #define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_TEMP_BED     80
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
@@ -2271,7 +2271,7 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
@@ -2479,7 +2479,7 @@
  *
  * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  */
-#define DISPLAY_CHARSET_HD44780 JAPANESE
+#define DISPLAY_CHARSET_HD44780 WESTERN
 
 /**
  * Info Screen Style (0:Classic, 1:Průša)
@@ -2494,7 +2494,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
@@ -2518,7 +2518,7 @@
 // This option overrides the default number of encoder pulses needed to
 // produce one step. Should be increased for high-resolution encoders.
 //
-//#define ENCODER_PULSES_PER_STEP 4
+#define ENCODER_PULSES_PER_STEP 4
 
 //
 // Use this option to override the number of step signals required to
@@ -2574,7 +2574,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 //#define INDIVIDUAL_AXIS_HOMING_SUBMENU
 
 //
@@ -2583,7 +2583,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -2872,7 +2872,7 @@
 //
 // Connect to EXP1 on RAMPS and compatible boards.
 //
-//#define CR10_STOCKDISPLAY
+#define CR10_STOCKDISPLAY
 
 //
 // Ender-2 OEM display, a variant of the MKS_MINI_12864
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 6557ad8..fa466e0 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -910,7 +910,7 @@
 
   // Safety: The probe needs time to recognize the command.
   //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
+  #define BLTOUCH_DELAY 500
 
   /**
    * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
@@ -936,7 +936,7 @@
    * differs, a mode set EEPROM write will be completed at initialization.
    * Use the option below to force an EEPROM write to a V3.1 probe regardless.
    */
-  //#define BLTOUCH_SET_5V_MODE
+  #define BLTOUCH_SET_5V_MODE
 
   // Safety: Enable voltage mode settings in the LCD menu.
   //#define BLTOUCH_LCD_VOLTAGE_MENU
@@ -1445,7 +1445,7 @@
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // Apply a timeout to low-priority status messages
   //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
@@ -2064,7 +2064,7 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
@@ -2393,16 +2393,16 @@
 #if BOTH(SDSUPPORT, DIRECT_STEPPING)
   #define BLOCK_BUFFER_SIZE  8
 #elif ENABLED(SDSUPPORT)
-  #define BLOCK_BUFFER_SIZE 16
+  #define BLOCK_BUFFER_SIZE 32
 #else
-  #define BLOCK_BUFFER_SIZE 16
+  #define BLOCK_BUFFER_SIZE 32
 #endif
 
 // @section serial
 
 // The ASCII buffer for serial input
 #define MAX_CMD_SIZE 96
-#define BUFSIZE 4
+#define BUFSIZE 64
 
 // Transmission to Host Buffer Size
 // To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@@ -2648,7 +2648,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.