Build Success v1
Successful build of 2072. Includes: BLTouch, MSDDE, Arc Support.
This commit is contained in:
icewolf08
+57
-57
@@ -371,9 +371,9 @@
|
||||
* Hotend Idle Timeout
|
||||
* Prevent filament in the nozzle from charring and causing a critical jam.
|
||||
*/
|
||||
//#define HOTEND_IDLE_TIMEOUT
|
||||
#define HOTEND_IDLE_TIMEOUT
|
||||
#if ENABLED(HOTEND_IDLE_TIMEOUT)
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (8*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
|
||||
#define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
|
||||
#define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
|
||||
@@ -395,9 +395,9 @@
|
||||
* The fan turns on automatically whenever any driver is enabled and turns
|
||||
* off (or reduces to idle speed) shortly after drivers are turned off.
|
||||
*/
|
||||
//#define USE_CONTROLLER_FAN
|
||||
#define USE_CONTROLLER_FAN
|
||||
#if ENABLED(USE_CONTROLLER_FAN)
|
||||
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
|
||||
#define CONTROLLER_FAN_PIN PC7 // Set a custom pin for the controller fan
|
||||
//#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
|
||||
//#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled.
|
||||
#define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
|
||||
@@ -682,7 +682,7 @@
|
||||
|
||||
// Safety: The probe needs time to recognize the command.
|
||||
// Minimum command delay (ms). Enable and increase if needed.
|
||||
//#define BLTOUCH_DELAY 500
|
||||
#define BLTOUCH_DELAY 500
|
||||
|
||||
/**
|
||||
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
|
||||
@@ -708,7 +708,7 @@
|
||||
* differs, a mode set eeprom write will be completed at initialization.
|
||||
* Use the option below to force an eeprom write to a V3.1 probe regardless.
|
||||
*/
|
||||
//#define BLTOUCH_SET_5V_MODE
|
||||
#define BLTOUCH_SET_5V_MODE
|
||||
|
||||
/**
|
||||
* Safety: Activate if connecting a probe with an unknown voltage mode.
|
||||
@@ -860,7 +860,7 @@
|
||||
// Increase the slowdown divisor for larger buffer sizes.
|
||||
#define SLOWDOWN
|
||||
#if ENABLED(SLOWDOWN)
|
||||
#define SLOWDOWN_DIVISOR 2
|
||||
#define SLOWDOWN_DIVISOR 8
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -1082,7 +1082,7 @@
|
||||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
@@ -1119,7 +1119,7 @@
|
||||
#endif // HAS_LCD_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
//#define LCD_DECIMAL_SMALL_XY
|
||||
@@ -1128,20 +1128,20 @@
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
// Show the E position (filament used) during printing
|
||||
//#define LCD_SHOW_E_TOTAL
|
||||
#define LCD_SHOW_E_TOTAL
|
||||
|
||||
#if ENABLED(SHOW_BOOTSCREEN)
|
||||
#define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
|
||||
#endif
|
||||
|
||||
#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && ANY(HAS_MARLINUI_U8GLIB, HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
|
||||
//#define SHOW_REMAINING_TIME // Display estimated time to completion
|
||||
#define SHOW_REMAINING_TIME // Display estimated time to completion
|
||||
#if ENABLED(SHOW_REMAINING_TIME)
|
||||
//#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
|
||||
//#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
|
||||
#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
|
||||
#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
|
||||
#endif
|
||||
|
||||
#if HAS_MARLINUI_U8GLIB
|
||||
@@ -1195,17 +1195,17 @@
|
||||
* an option on the LCD screen to continue the print from the last-known
|
||||
* point in the file.
|
||||
*/
|
||||
//#define POWER_LOSS_RECOVERY
|
||||
#define POWER_LOSS_RECOVERY
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
|
||||
#define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
|
||||
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
|
||||
//#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
|
||||
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
#define POWER_LOSS_PURGE_LEN 10 // (mm) Length of filament to purge on resume
|
||||
#define POWER_LOSS_RETRACT_LEN 1.5 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
|
||||
// especially with "vase mode" printing. Set too high and vases cannot be continued.
|
||||
@@ -1235,26 +1235,26 @@
|
||||
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
|
||||
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
|
||||
*/
|
||||
//#define SDCARD_SORT_ALPHA
|
||||
#define SDCARD_SORT_ALPHA
|
||||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 G-code.
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
//#define SCROLL_LONG_FILENAMES
|
||||
#define SCROLL_LONG_FILENAMES
|
||||
|
||||
// Leave the heaters on after Stop Print (not recommended!)
|
||||
//#define SD_ABORT_NO_COOLDOWN
|
||||
@@ -1264,7 +1264,7 @@
|
||||
* This feature must be enabled with "M540 S1" or from the LCD menu.
|
||||
* To have any effect, endstops must be enabled during SD printing.
|
||||
*/
|
||||
//#define SD_ABORT_ON_ENDSTOP_HIT
|
||||
#define SD_ABORT_ON_ENDSTOP_HIT
|
||||
|
||||
/**
|
||||
* This option makes it easier to print the same SD Card file again.
|
||||
@@ -1338,7 +1338,7 @@
|
||||
*
|
||||
* :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
|
||||
*/
|
||||
//#define SDCARD_CONNECTION LCD
|
||||
#define SDCARD_CONNECTION ONBOARD
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
@@ -1420,7 +1420,7 @@
|
||||
//#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
|
||||
//#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
|
||||
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
|
||||
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar
|
||||
#define STATUS_HEAT_PERCENT // Show heating in a progress bar
|
||||
//#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
|
||||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
|
||||
|
||||
@@ -1603,18 +1603,18 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 4 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
@@ -1626,10 +1626,10 @@
|
||||
|
||||
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
|
||||
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@@ -1891,16 +1891,16 @@
|
||||
#if BOTH(SDSUPPORT, DIRECT_STEPPING)
|
||||
#define BLOCK_BUFFER_SIZE 8
|
||||
#elif ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 16
|
||||
#define BLOCK_BUFFER_SIZE 32
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16
|
||||
#define BLOCK_BUFFER_SIZE 32
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
||||
// The ASCII buffer for serial input
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
#define BUFSIZE 64
|
||||
|
||||
// Transmission to Host Buffer Size
|
||||
// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
|
||||
@@ -1909,7 +1909,7 @@
|
||||
// For debug-echo: 128 bytes for the optimal speed.
|
||||
// Other output doesn't need to be that speedy.
|
||||
// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
|
||||
#define TX_BUFFER_SIZE 0
|
||||
#define TX_BUFFER_SIZE 32
|
||||
|
||||
// Host Receive Buffer Size
|
||||
// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
|
||||
@@ -2087,14 +2087,14 @@
|
||||
* Requires NOZZLE_PARK_FEATURE.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 200 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
@@ -2103,7 +2103,7 @@
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 200 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
@@ -2125,10 +2125,10 @@
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
@@ -2264,7 +2264,7 @@
|
||||
#define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
|
||||
|
||||
#if AXIS_IS_TMC(X)
|
||||
#define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current.
|
||||
#define X_CURRENT 580 // (mA) RMS current. Multiply by 1.414 for peak current.
|
||||
#define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing
|
||||
#define X_MICROSTEPS 16 // 0..256
|
||||
#define X_RSENSE 0.11
|
||||
@@ -2280,7 +2280,7 @@
|
||||
#endif
|
||||
|
||||
#if AXIS_IS_TMC(Y)
|
||||
#define Y_CURRENT 800
|
||||
#define Y_CURRENT 580
|
||||
#define Y_CURRENT_HOME Y_CURRENT
|
||||
#define Y_MICROSTEPS 16
|
||||
#define Y_RSENSE 0.11
|
||||
@@ -2296,7 +2296,7 @@
|
||||
#endif
|
||||
|
||||
#if AXIS_IS_TMC(Z)
|
||||
#define Z_CURRENT 800
|
||||
#define Z_CURRENT 580
|
||||
#define Z_CURRENT_HOME Z_CURRENT
|
||||
#define Z_MICROSTEPS 16
|
||||
#define Z_RSENSE 0.11
|
||||
@@ -2328,7 +2328,7 @@
|
||||
#endif
|
||||
|
||||
#if AXIS_IS_TMC(E0)
|
||||
#define E0_CURRENT 800
|
||||
#define E0_CURRENT 650
|
||||
#define E0_MICROSTEPS 16
|
||||
#define E0_RSENSE 0.11
|
||||
#define E0_CHAIN_POS -1
|
||||
@@ -2426,14 +2426,14 @@
|
||||
* on the same serial port, either here or in your board's pins file.
|
||||
*/
|
||||
#define X_SLAVE_ADDRESS 0
|
||||
#define Y_SLAVE_ADDRESS 0
|
||||
#define Z_SLAVE_ADDRESS 0
|
||||
#define Y_SLAVE_ADDRESS 2
|
||||
#define Z_SLAVE_ADDRESS 1
|
||||
#define X2_SLAVE_ADDRESS 0
|
||||
#define Y2_SLAVE_ADDRESS 0
|
||||
#define Z2_SLAVE_ADDRESS 0
|
||||
#define Z3_SLAVE_ADDRESS 0
|
||||
#define Z4_SLAVE_ADDRESS 0
|
||||
#define E0_SLAVE_ADDRESS 0
|
||||
#define E0_SLAVE_ADDRESS 3
|
||||
#define E1_SLAVE_ADDRESS 0
|
||||
#define E2_SLAVE_ADDRESS 0
|
||||
#define E3_SLAVE_ADDRESS 0
|
||||
@@ -2474,7 +2474,7 @@
|
||||
* Define you own with
|
||||
* { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
|
||||
*/
|
||||
#define CHOPPER_TIMING CHOPPER_DEFAULT_12V
|
||||
#define CHOPPER_TIMING CHOPPER_DEFAULT_24V
|
||||
|
||||
/**
|
||||
* Monitor Trinamic drivers
|
||||
@@ -2487,7 +2487,7 @@
|
||||
* M912 - Clear stepper driver overtemperature pre-warn condition flag.
|
||||
* M122 - Report driver parameters (Requires TMC_DEBUG)
|
||||
*/
|
||||
//#define MONITOR_DRIVER_STATUS
|
||||
#define MONITOR_DRIVER_STATUS
|
||||
|
||||
#if ENABLED(MONITOR_DRIVER_STATUS)
|
||||
#define CURRENT_STEP_DOWN 50 // [mA]
|
||||
@@ -2550,16 +2550,16 @@
|
||||
|
||||
#if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
|
||||
// TMC2209: 0...255. TMC2130: -64...63
|
||||
#define X_STALL_SENSITIVITY 8
|
||||
#define X_STALL_SENSITIVITY 75
|
||||
#define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
|
||||
#define Y_STALL_SENSITIVITY 8
|
||||
#define Y_STALL_SENSITIVITY 75
|
||||
#define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
|
||||
//#define Z_STALL_SENSITIVITY 8
|
||||
//#define Z_STALL_SENSITIVITY 75
|
||||
//#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
|
||||
//#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
|
||||
//#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
|
||||
//#define SPI_ENDSTOPS // TMC2130 only
|
||||
//#define IMPROVE_HOMING_RELIABILITY
|
||||
#define IMPROVE_HOMING_RELIABILITY
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -2578,7 +2578,7 @@
|
||||
* Beta feature!
|
||||
* Create a 50/50 square wave step pulse optimal for stepper drivers.
|
||||
*/
|
||||
//#define SQUARE_WAVE_STEPPING
|
||||
#define SQUARE_WAVE_STEPPING
|
||||
|
||||
/**
|
||||
* Enable M122 debugging command for TMC stepper drivers.
|
||||
@@ -2899,7 +2899,7 @@
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_STATE LOW // Set to "HIGH" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT false // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
|
||||
#define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
|
||||
|
||||
@@ -3272,7 +3272,7 @@
|
||||
*
|
||||
* Implement M486 to allow Marlin to skip objects
|
||||
*/
|
||||
//#define CANCEL_OBJECTS
|
||||
#define CANCEL_OBJECTS
|
||||
|
||||
/**
|
||||
* I2C position encoders for closed loop control.
|
||||
|
||||
Reference in New Issue
Block a user